Elegoo 3D Printers Forum - General Troubleshooting

Users browsing this forum: 10 Guest(s)

Pages (16): « Previous 1 2 3 4 5 … 16 Next »

Mark this forum read General Troubleshooting
Thread / Author		Replies	Views	Rating	Last Post [asc]
	Poor quality on vertical walls KenW	0	725	0 Vote(s) - 0 out of 5 in Average	12-02-2023, 09:14 AM Last Post: KenW
	New Saturn 3 12k Does not recognise when I have set Home spooookie1	0	891	0 Vote(s) - 0 out of 5 in Average	11-28-2023, 10:02 AM Last Post: spooookie1
	Reach Printer through VPN schwummelwummel	0	933	0 Vote(s) - 0 out of 5 in Average	11-17-2023, 09:58 AM Last Post: schwummelwummel
	Stopping mid print (Pages: 1 2 ) archaon	10	22,669	0 Vote(s) - 0 out of 5 in Average	10-09-2023, 10:54 AM Last Post: MacDime224
	Creases in the printed model Emperorbaz	0	1,045	0 Vote(s) - 0 out of 5 in Average	09-29-2023, 05:14 AM Last Post: Emperorbaz
	Printer is making a weird sound Chloe west	0	1,194	0 Vote(s) - 0 out of 5 in Average	09-14-2023, 06:18 AM Last Post: Chloe west
	When is a square not a square! Fingers	0	1,561	0 Vote(s) - 0 out of 5 in Average	07-20-2023, 07:20 AM Last Post: Fingers
	Build plate's spring gets stuck after thighening the screws. Doesn't lower properly BadPotato	3	5,551	0 Vote(s) - 0 out of 5 in Average	07-06-2023, 01:59 AM Last Post: Nutters
	saturn polarizer? gaiernorbert	2	4,010	0 Vote(s) - 0 out of 5 in Average	06-16-2023, 08:56 PM Last Post: rob12770
	Saturn only print the First layers Matocs	0	1,118	0 Vote(s) - 0 out of 5 in Average	06-12-2023, 01:53 PM Last Post: Matocs
	Weird failure. Prints are....compressed? RBTGames	0	1,342	0 Vote(s) - 0 out of 5 in Average	05-19-2023, 05:17 PM Last Post: RBTGames
	Building Plate Goes Too High Up After Prints Finish Beefula	1	5,953	0 Vote(s) - 0 out of 5 in Average	05-04-2023, 03:59 PM Last Post: Katmodel
	Chitubox and Elegoo Mars printing problem boblinux	0	1,343	0 Vote(s) - 0 out of 5 in Average	03-24-2023, 10:20 AM Last Post: boblinux
	What does the "home" button actually do? jubuttib	0	1,704	0 Vote(s) - 0 out of 5 in Average	03-15-2023, 05:09 AM Last Post: jubuttib
	Exposure Test Fails, Saturn S, full screen with black line down center GordonVincent	0	1,667	0 Vote(s) - 0 out of 5 in Average	03-12-2023, 10:56 AM Last Post: GordonVincent
	resolution of the sliced file does not match screen-1440 a-guillotine	9	35,657	0 Vote(s) - 0 out of 5 in Average	01-06-2023, 07:19 PM Last Post: Jay_D
	Neptune X won't start printing W1uvakind	0	1,612	0 Vote(s) - 0 out of 5 in Average	12-21-2022, 05:23 PM Last Post: W1uvakind
	Saturn 2: Brittle prints 5oh86	2	3,371	0 Vote(s) - 0 out of 5 in Average	12-01-2022, 09:03 AM Last Post: 5oh86
	Distorted prints Skillster	1	2,472	0 Vote(s) - 0 out of 5 in Average	11-30-2022, 04:11 AM Last Post: billtodd
	Memory error 200000 Tineriusguy	2	6,462	0 Vote(s) - 0 out of 5 in Average	11-24-2022, 08:18 AM Last Post: kamper

Pages (16): « Previous 1 2 3 4 5 … 16 Next »

New Posts

Hot Thread (New)

Hot Thread (No New)

No New Posts

Contains Posts by You

Closed Thread

Forum Jump:

Login
Username/Email:
Password:	Lost Password?
	Remember me